What's new

Solved Ask for information Xkit X360ACE V4

  • Thread starter Hafidi
  • Start date
  • Views 2,802
Hafidi

Hafidi

Newbie
Messages
34
Reaction score
0
Points
45
Sin$
0
Hello community members,

I've already have some experience with PS3 Jailbeak but this it will be my first step and try to jailbreak Xbox .
Some tools i have :
  • Xbox 360 Slim 2010-05-10 12v---10.83 Model 1439 ( Trinity i think ) .
  • Chip X360ACE V4 .
  • Nand X .
  • CPU Post Fix Adapter.
  • All soldering and repair tools .( I've a phone repair shop )
My question is with what should i start ?

Any advises are welcome just be patient with me i'm noob with Xbox world .
 
Hafidi

Hafidi

Newbie
Messages
34
Reaction score
0
Points
45
Sin$
0
XeDevn

XeDevn

Enthusiast
Messages
338
Reaction score
32
Points
105
Sin$
7
Well thank you sir, i'll post my experiment, i hope everything will be fine.
Is there anything to be care about it?
No problem! Just be careful soldering really. Use plenty of flux, don’t hold onto a point very long, and most importantly practice! If you have any kind of circuit board just practice soldering onto pads. There’s also plenty of good soldering tutorials on YouTube. Just don’t rip a pad and you’ll be ok! Lol
 
Hafidi

Hafidi

Newbie
Messages
34
Reaction score
0
Points
45
Sin$
0
No problem! Just be careful soldering really. Use plenty of flux, don’t hold onto a point very long, and most importantly practice! If you have any kind of circuit board just practice soldering onto pads. There’s also plenty of good soldering tutorials on YouTube. Just don’t rip a pad and you’ll be ok! Lol
Thank you, i'll try it .
Please Administrators don't close thread till i report results .

Best regards.
 
Newsk

Newsk

Contributor
Messages
2,602
Solutions
5
Reaction score
348
Points
350
Sin$
7
Very first step is; read the nand getting 2 matching nand dumps.(back them up outside of jrunner ) Then create ecc image and write it to the nand . Have you done that ?
 
Hafidi

Hafidi

Newbie
Messages
34
Reaction score
0
Points
45
Sin$
0
Very first step is; read the nand getting 2 matching nand dumps.(back them up outside of jrunner ) Then create ecc image and write it to the nand . Have you done that ?
Thank you for reply, which software i need to use and which pinouts should i follow ?
 
Hafidi

Hafidi

Newbie
Messages
34
Reaction score
0
Points
45
Sin$
0
i'm sorry i'm newbie be patient with me, because i've seen many videos and topics and many users said that the ACE V4 little different from V3 . i don't know and i don't want to take any risks .
 
Newsk

Newsk

Contributor
Messages
2,602
Solutions
5
Reaction score
348
Points
350
Sin$
7
. I would first make sure the console still boots by removing the 3.3v from the chip and boot it up . Assuming it still boots move forward with reading your nand using your nand x and jrunner. You'll need to install the nandx driver on your pc to get jrunner able to use it.

To install driver u have to disable driver signature enforcement(wont work otherwise ) then plug it in to USB and find it in device manager then right click and manually install driver . Point it to the jrunner folder/common/drivers . Then say install anyways when prompted.
 
Hafidi

Hafidi

Newbie
Messages
34
Reaction score
0
Points
45
Sin$
0
. I would first make sure the console still boots by removing the 3.3v from the chip and boot it up . Assuming it still boots move forward with reading your nand using your nand x and jrunner. You'll need to install the nandx driver on your pc to get jrunner able to use it.

To install driver u have to disable driver signature enforcement(wont work otherwise ) then plug it in to USB and find it in device manager then right click and manually install driver . Point it to the jrunner folder/common/drivers . Then say install anyways when prompted.
thank you man ♥ i'll post updates of my work :wink:
 
Top Bottom
Login
Register