What's new

Solved RGH 1.2 or R-Jtag CR4?

  • Thread starter XenonFX
  • Start date
  • Views 3,656
XenonFX

XenonFX

Enthusiast
Messages
117
Reaction score
7
Points
70
Sin$
7
I've modded my fair share of xbox's and was looking for some advice for my personal console. Which exploit is better, R-Jtag with a CR4 or RGH 1.2? I've done RGH 1.2 a couple of times with the results of instant boot. Naturally I'm curious about R-Jtag and was wondering if it was worth picking up a CR4. I have a 256MB Jasper that I plan on modding. I figured the CR4 would work better with a Demon vs a bootleg cr rev c. For this Jasper I plan on doing a dual nand setup with xebuild and RGloader. 
Just realized I put this in the wrong forum will repost in the right place
 
Killjoy666

Killjoy666

Getting There
Messages
1,649
Reaction score
233
Points
190
Sin$
0
I've modded my fair share of xbox's and was looking for some advice for my personal console. Which exploit is better, R-Jtag with a CR4 or RGH 1.2? I've done RGH 1.2 a couple of times with the results of instant boot. Naturally I'm curious about R-Jtag and was wondering if it was worth picking up a CR4. I have a 256MB Jasper that I plan on modding. I figured the CR4 would work better with a Demon vs a bootleg cr rev c. For this Jasper I plan on doing a dual nand setup with xebuild and RGloader. 
Just realized I put this in the wrong forum will repost in the right place
RGH 1.2 Works With Demon As Well.
 
Newsk

Newsk

Contributor
Messages
2,602
Solutions
5
Reaction score
348
Points
350
Sin$
7
No, You Will Get Much Better Results With RGH 1.2.
agreed!:smile:

and yes just install matrix/ or rev c and install demon as normal. no connection between them required (i.e. cr_en) cause 1.2 files will boot stocK nand or rgh nand.
 
Last edited:
B

Bullet21

Newbie
Messages
12
Reaction score
1
Points
30
Sin$
0
I'm about to mod my phat Xbox 360 and I haven't modded an Xbox since the original......

I was hoping you guys could point me in the right direction please...


I'm reading that the RGH 1.2 is the way to go??

I need to order a xecuter with the programer and can't seem to find a good link on where to buy from??? I'm in the US....

Also how do I identify which bios I have or does it matter??

I'm assuming terms like "Jasper" is describing the bios chip??

Nice website for sure!!
 
Killjoy666

Killjoy666

Getting There
Messages
1,649
Reaction score
233
Points
190
Sin$
0
I'm about to mod my phat Xbox 360 and I haven't modded an Xbox since the original......

I was hoping you guys could point me in the right direction please...


I'm reading that the RGH 1.2 is the way to go??

I need to order a xecuter with the programer and can't seem to find a good link on where to buy from??? I'm in the US....

Also how do I identify which bios I have or does it matter??

I'm assuming terms like "Jasper" is describing the bios chip??

Nice website for sure!!
Check On eBay.

You Will Need A Coolrunner Rev C + Jr Programmer V2.

Well You Said It Was A 256MB Jasper So Dashboard Won't Matter.
 
B

Bullet21

Newbie
Messages
12
Reaction score
1
Points
30
Sin$
0
That was the other guy that said he had a 256mg Jasper not me.......

So is Jasper referring to the dashboard???

I'm still trying to figure out what I need.......

I found a "rev c" and a "rev d" version........would the revision D board not work???

Can someone either tell me how to identify my Xbox 360 correctly so I order the right parts.....or point me to a thread that explains what the term "Jasper" is referring to???

Confused more than ever now after reading killjoy666's response......LMAO!!!

Thanks!
 
Newsk

Newsk

Contributor
Messages
2,602
Solutions
5
Reaction score
348
Points
350
Sin$
7
Jasper is the motherboard . Look at where your power supply plugs in to identify which motherboard u have https://goo.gl/images/xDYjVu.
A rev c will work great but other chips will work for rgh 1.2 aswell (rev d,matrix v1 , v3, even an acev2 v3 )
U also will need something to read /write nand and write timings to your glitcher like a jrprogrammer v2 or nand x
 
B

Bullet21

Newbie
Messages
12
Reaction score
1
Points
30
Sin$
0
Jasper is the motherboard . Look at where your power supply plugs in to identify which motherboard u have https://goo.gl/images/xDYjVu.
A rev c will work great but other chips will work for rgh 1.2 aswell (rev d,matrix v1 , v3, even an acev2 v3 )
U also will need something to read /write nand and write timings to your glitcher like a jrprogrammer v2 or nand x

Awesome!!! Thank you very much!! Exactly what I needed........

So it looks like I have a XENON according to the image......

My production date is 12/13/2006 and it has the switch for HDTV instead of a HDMI port.......

http://www.ebay.com/itm/151441685451

Will this work?
 
As an eBay Associate we earn from qualifying purchases.
Top Bottom
Login
Register