What's new

Solved IM GOING CRAZZZY 4GB V2 CORONA

  • Thread starter JustMattyModding
  • Start date
  • Views 2,962
J

JustMattyModding

Enthusiast
Messages
120
Reaction score
5
Points
70
Sin$
7
IM GOING CRAZY!

So I have the following :
Qsb- tx corona 4gb nand rw kit

And JR PROGRAMMER V2 for xbox slim

Coolrunner Rev C - UK Stock



So

dHduEDj.jpg

UNKkjp9.jpg

JGO5sWI.jpg

LjtgxBa.jpg

1)I have soldered the Nand rw kit into place.
2) I Then connected the ribbon to qsb to sd card reader and put the switch on to R/W
3) I tried connecting the sd drive into pc ( using win 10 with device signed off )this is what come up in device manager:
QKHVypIm.png

What do I do next?

ADD ME ON SKYPE <3 [email protected] / matty modding
PLEASE HELP ME IL SEND n**** OF MY IMAGINARY GIRLFRIEND
 
Newsk

Newsk

Contributor
Messages
2,602
Solutions
5
Reaction score
348
Points
350
Sin$
7
make sure non of those are shorted together. use a voltmeter and check in diode mode or in ohms for continuity.(in your first pic it appears the 2nd and 3rd are.)
also a lot of those generic kits are just shight and have too much resistance in them somewhere along the line.

put power to xbox first, then put sd into adapter and insert into pc. if you have it plugged into pc and then plug in xbox it wont read most of the time(for me anyways)
 
J

JoinTheResistance

Dead to the world, alive for the journey...
Messages
4,669
Reaction score
1,100
Points
1,045
Sin$
7
As already said, remove the shorts! Though, I think that two of the pads were shorted on the motherboard anyway. Also, if it still doesn't work, you should try a different SD card reader. A lot of adapters just aren't compatible.
 
J

JustMattyModding

Enthusiast
Messages
120
Reaction score
5
Points
70
Sin$
7
As already said, remove the shorts! Though, I think that two of the pads were shorted on the motherboard anyway. Also, if it still doesn't work, you should try a different SD card reader. A lot of adapters just aren't compatible.


Hey sorry am I being stupid , dos it matter if the there solder bridged at top?
g7qjuJH.png


Also how do I check the continuity ( as In what points do I probe :smile:
 
Last edited:
Newsk

Newsk

Contributor
Messages
2,602
Solutions
5
Reaction score
348
Points
350
Sin$
7
To check for shorts put on ohms and test between the pads . Although some may be connected anyways even without the qsb soldered on. If still not reading go get another cheap card reader at like walmart or something and try that .
 
J

JustMattyModding

Enthusiast
Messages
120
Reaction score
5
Points
70
Sin$
7
No they can't be bridged.
Thanks silly me ...

To check for shorts put on ohms and test between the pads . Although some may be connected anyways even without the qsb soldered on. If still not reading go get another cheap card reader at like walmart or something and try that .

Ok il try that thanks, I did order 3 different card readers (uk so not much choice lol)
 
J

JustMattyModding

Enthusiast
Messages
120
Reaction score
5
Points
70
Sin$
7
This was from a post on the forums I saw:
Dosnt say anything about a qsb upgrade?


There are 6 Different Coronas.

The Xbox 360 S has v1/2/3/4.
The Xbox 360 E has v5/6.


Corona v1 - Glitch Chip | QSB | JR-Programmer 2
Corona v2 - Glitch Chip | QSB | 4GB R/W QSB
Corona v3 - Glitch Chip | QSB | JR-Programmer 2 | Post Fix Adapter
Corona v4 - Glitch Chip | QSB | 4GB R/W QSB | Post Fix Adapter
Corona v5 - Glitch Chip | QSB | JR-Programmer 2 | Post Fix Adapter
Corona v6 - Glitch Chip | QSB | 4GB R/W QSB | Post Fix Adapter
 
Killjoy666

Killjoy666

Getting There
Messages
1,649
Reaction score
233
Points
190
Sin$
0
This was from a post on the forums I saw:
Dosnt say anything about a qsb upgrade?


There are 6 Different Coronas.

The Xbox 360 S has v1/2/3/4.
The Xbox 360 E has v5/6.


Corona v1 - Glitch Chip | QSB | JR-Programmer 2
Corona v2 - Glitch Chip | QSB | 4GB R/W QSB
Corona v3 - Glitch Chip | QSB | JR-Programmer 2 | Post Fix Adapter
Corona v4 - Glitch Chip | QSB | 4GB R/W QSB | Post Fix Adapter
Corona v5 - Glitch Chip | QSB | JR-Programmer 2 | Post Fix Adapter
Corona v6 - Glitch Chip | QSB | 4GB R/W QSB | Post Fix Adapter
Coolrunner Rev C Doesn't Have A 48mhz Oscillator. Only Way To Get A Rev C To Work On A Corona Is By Using A Corona Upgrade Qsb Which Has A Oscillator Installed Onto It.

You Could Swap The Chip For A.
•Cr3 Lite
•X360ace V3
•Coolrunner Rev D
•x360run
•Matrix V3
Basically Any Glitcher With A 48mhz Oscillator Installed Into It.
 
J

JoinTheResistance

Dead to the world, alive for the journey...
Messages
4,669
Reaction score
1,100
Points
1,045
Sin$
7
Ok il try that thanks, I did order 3 different card readers (uk so not much choice lol)
This is the one that's been proven to work by me and many others: http://www.ebay.com/itm/Sabrent-Sup...639759?hash=item1a2fe4490f:g:s-0AAOSwmgJY5-DE

Coolrunner Rev C Doesn't Have A 48mhz Oscillator. Only Way To Get A Rev C To Work On A Corona Is By Using A Corona Upgrade Qsb Which Has A Oscillator Installed Onto It.
Just a tiny correction, you can simply solder a 48MHz oscillator to the Rev C, no need for the whole adapter.
Basically Any Glitcher With A 48mhz Oscillator Installed Into It.
Actually, any frequency that's high enough can work. The aces for example use a 150MHz reference clock, while the rest of the mentioned chips can be modded to use a 100MHz clock. Technically, they can probably go even higher, though there probably won't be a huge benefit.
 
As an eBay Associate we earn from qualifying purchases.
J

JustMattyModding

Enthusiast
Messages
120
Reaction score
5
Points
70
Sin$
7
Thanks all for repleys I have ordered a ace v3 chip !
I went over the pads again and I think I sorted the problem (my bad soldering skills :tongue: or I blame the tiny pads lol )
I'm awaiting for postman to be arrive with some chip readers, will update thread when they arrive
 
Top Bottom
Login
Register