X360 Ace V3 chip Error

Discussion in 'Xbox 360 Support' started by Tgivenchy, May 10, 2018 with 24 replies and 281 views.

  1. Tgivenchy

    Tgivenchy Newbie

    Messages:
    79
    Ratings:
    0
    Every time I tried to change the timing file on my Ace v3 chip J runner gives me the
    0x0002 Error ?

    How can I fix this ?

    Also everytime I tried to change the file the led on the chip disappears

    Is my Ace Chip mess up ?

    Another thing I notice there’s a lot of fake Ace chips out there .. can that be the problem I order one and I think I got the fake one where can I get the real one coming from US soil


     
  2. OP
    Tgivenchy

    Tgivenchy Newbie

    Messages:
    79
    Ratings:
    0
  3. afterjo

    afterjo Enthusiast

    Messages:
    215
    Ratings:
    21
  4. OP
    Tgivenchy

    Tgivenchy Newbie

    Messages:
    79
    Ratings:
    0
    I did I know my NAND X is ok cause I can read and write with it but I think is

    The Nand-X to CR programming cable maybe mess up idk
     
  5. afterjo

    afterjo Enthusiast

    Messages:
    215
    Ratings:
    21
    you may insert your cable wrong way, upside down or whatever. because pins for programing don't have slot, so you can insert in wrong side.
     
  6. OP
    Tgivenchy

    Tgivenchy Newbie

    Messages:
    79
    Ratings:
    0
     
  7. afterjo

    afterjo Enthusiast

    Messages:
    215
    Ratings:
    21
  8. OP
    Tgivenchy

    Tgivenchy Newbie

    Messages:
    79
    Ratings:
    0
    I tried it in every way when I put it on the chip my NAND X would disconnect and re connect it’s self just not reading any chips
     
  9. afterjo

    afterjo Enthusiast

    Messages:
    215
    Ratings:
    21
    you need to solder this thing. Otherwise you have poor connection or no connection at all.
     
  10. OP
    Tgivenchy

    Tgivenchy Newbie

    Messages:
    79
    Ratings:
    0
    Solder what ? The wires to the chip ? In order to get a solid connection?
     
  11. Doom94

    Doom94 Enthusiast

    Messages:
    147
    Ratings:
    7
    A couple of NANDXs I had did the same I have no solution. My JRP v2 worked perfectly though.
     
  12. OP
    Tgivenchy

    Tgivenchy Newbie

    Messages:
    79
    Ratings:
    0
    so now i need a JRP damn
     
  13. nullrootix

    nullrootix Newbie

    Messages:
    31
    Ratings:
    0
    OP if you take the smooth side of your programming cable and place it so the smooth side s in then apply a small amount of pressure when flashing the timing file to the chip. You need to be careful with fakes as they can toast the cpu and kill your xbox :frown: That has happened to me
    For as far as buying from a us supplier you can get them from TheWeekendModder pre-programmed for a few extra bucks

    Spot fakes from real:
    [​IMG]
    Please also note that the fakes may look the same to the real with the r22 and D point but the chip will be black
     
    Last edited: May 16, 2018
  14. OP
    Tgivenchy

    Tgivenchy Newbie

    Messages:
    79
    Ratings:
    0
    Thanks for the info but theweekendmodder already sent me 2 fake Ace v3 chips which both didn’t work smh

    [Click here to view the link]
     
  15. OP
    Tgivenchy

    Tgivenchy Newbie

    Messages:
    79
    Ratings:
    0
    Where can I buy real Glitch chips in US soil ???
     
  16. nullrootix

    nullrootix Newbie

    Messages:
    31
    Ratings:
    0
    Short answer: sorta, both the original and the fakes are produced in china with the amount of fakes flying about atm, your probally better off buying a coolrunner rev C/D, REV D's are clones but work very well as seen here:

    I have never had a issue with rev c's on a rgh 1.2 install
    i did find this link here:[Click here to view the link]
    And the chip looks legit but have never orded from them as i'm from the uk
     
  17. OP
    Tgivenchy

    Tgivenchy Newbie

    Messages:
    79
    Ratings:
    0
    Where can I find the CR4 XL ?
     
  18. nullrootix

    nullrootix Newbie

    Messages:
    31
    Ratings:
    0
    I personally can't find them my self in the uk but modchipcental should have them :biggrin:
     
  19. OP
    Tgivenchy

    Tgivenchy Newbie

    Messages:
    79
    Ratings:
    0
    Thanks for the info my guy one last question what chip would you recommend me for a Corona V3 ? Or should I just go for the CR4XL chip ?

    Or go with a Matrix or Ace ?
     
  20. nullrootix

    nullrootix Newbie

    Messages:
    31
    Ratings:
    0
    i've heard good things about both chips if i was doing a corona i'd use a cr rev D or a cr4xl with the amount of fake ace's around atm i'd avoid them at the moment
    Matrix chips require 32awg/kynar wire

    But coolrunners are far less hassle you program the chip as it has the programming headers unlike acev3/matrix -_- and solder the chip