What's new

Solved Spike at KPROBE on burned backup

  • Thread starter Jellonaw
  • Start date
  • Views 388
Jellonaw

Jellonaw

Newbie
Messages
5
Reaction score
2
Points
45
Sin$
0
I have this weird spike on my kprobe when layer changes. And I got the disc is not supported error on Xbox. ImgBurn burned it fine using the tutorial on this site. And yes, my Xbox is flashed. Disks used were Verbatim MKM-003, burn speed 4x and OPC enabled.

Thanks for the help already :smile:

f412b2f69a237f34e668bc4e55115468.png
 
Last edited:
Jellonaw

Jellonaw

Newbie
Messages
5
Reaction score
2
Points
45
Sin$
0
Try burning at 2x maybe? You might want to check this too:
http://www.ixtreme.net/open-forum/29528-massive-spike-pi-pif-kprobe.html
I switched to 2x and OPC off. And these are the results:
Date : 8.1.2016 16:28:45
Model : 1-2-0-0 F:TSSTcorpCDDVDW TS-H653R SC01
Disc : DVD+R DL , MKM003 [Mitsubishi Chemical Corporation]
Speed : 4x
ECC blocks sum (PI/PIF) : 8/1
Scanned range : 0 - 4267008
Sampling count : 250938
Errors : 0
PI Max : 21
PI Average : 1,39
PI Total : 43490
PIF Max : 4
PIF Average : 0,07
PIF Total : 2214

but when I start the game screen stays blank O.o

I did the abgx3 check correctly
 
AlienFreek01

AlienFreek01

Now with fries
Messages
1,140
Reaction score
295
Points
240
Sin$
0
I switched to 2x and OPC off. And these are the results:
Date : 8.1.2016 16:28:45
Model : 1-2-0-0 F:TSSTcorpCDDVDW TS-H653R SC01
Disc : DVD+R DL , MKM003 [Mitsubishi Chemical Corporation]
Speed : 4x
ECC blocks sum (PI/PIF) : 8/1
Scanned range : 0 - 4267008
Sampling count : 250938
Errors : 0
PI Max : 21
PI Average : 1,39
PI Total : 43490
PIF Max : 4
PIF Average : 0,07
PIF Total : 2214

but when I start the game screen stays blank O.o

I did the abgx3 check correctly
What game? Also speed was still 4x, but I doubt that's the problem
 
AlienFreek01

AlienFreek01

Now with fries
Messages
1,140
Reaction score
295
Points
240
Sin$
0
I used the Payload BurnerMax
OK so I'll assume your drive supports that then... Do all of your settings match these?:
Click on Advanced Settings then LiteOn and set it up in the following way(Remember to redo it every time after using the Payload tool, the Payload Tool resets it to default settings again):

Force Hypertuning - Enabled
Online Hypertung - Disabled
Smartburn - Enabled
Overspeed - Enabled
OPC history - Do not clear

General IMGBurn settings

Set up the settings like this in IMGBurn's general settings:

I/O tab -> Page 2 -> Set Buffer to 150MB

Write tab -> Perform OPC Before Write ON
I'm going to assume you have looked at the full tut, but if you haven't you can find it here

Have you burned other xgd3 games successfully? 
I said xbg3 instead of xgd3:banghead:... it's been awhile lol
 
Last edited:
Jellonaw

Jellonaw

Newbie
Messages
5
Reaction score
2
Points
45
Sin$
0
OK so I'll assume your drive supports that then... Do all of your settings match these?:
Click on Advanced Settings then LiteOn and set it up in the following way(Remember to redo it every time after using the Payload tool, the Payload Tool resets it to default settings again):

Force Hypertuning - Enabled
Online Hypertung - Disabled
Smartburn - Enabled
Overspeed - Enabled
OPC history - Do not clear

General IMGBurn settings

Set up the settings like this in IMGBurn's general settings:

I/O tab -> Page 2 -> Set Buffer to 150MB

Write tab -> Perform OPC Before Write ON
I'm going to assume you have looked at the full tut, but if you haven't you can find it here

Have you burned other xgd3 games successfully? 
I said xbg3 instead of xgd3:banghead:... it's been awhile lol
I installed TU1 to it and now it started :biggrin:
 
Top Bottom
Login
Register