What's new

Solved RGH Trinity wont boot with ACE V3, sometimes works with Matrix V3

S

smailer

Enthusiast
Messages
282
Reaction score
3
Hello,

Have strange situation XBOX Trinity not working (just gliching green light, wont boot) with Ace v3 at all.... (changes couples chips, hundred timming files)
With Matrix V3 worked couples times, but now still not boot at all.

Where can be problem?

https://photos.app.goo.gl/fqoL92qgvBRmWgd76
 
N

Noobert

RGH/Flashing Support
VIP
Retired
Messages
8,385
Reaction score
4,623
Hello,

Have strange situation XBOX Trinity not working (just gliching green light, wont boot) with Ace v3 at all.... (changes couples chips, hundred timming files)
With Matrix V3 worked couples times, but now still not boot at all.

Where can be problem?

https://photos.app.goo.gl/fqoL92qgvBRmWgd76
Trinity with Matrix doesn't need the oscillator crystal.

Remove it.
 
N

Noobert

RGH/Flashing Support
VIP
Retired
Messages
8,385
Reaction score
4,623
but i have allready removed resistor, still i need remove crystal?
Oh sorry, I didn't notice that :tongue:

What timing file did you flash to the Matrix?
 
S

smailer

Enthusiast
Messages
282
Reaction score
3
Oh sorry, I didn't notice that :tongue:

What timing file did you flash to the Matrix?
muffin_5-1_dt
muffin_5-2_dt
muffin_6-1_dt
muffin_6-2_dt
muffin_7-1_dt
muffin_7-2_dt


muffin_7-1_dt yesterday worked with this, so today decided to pack it and not working now..
 
N

Noobert

RGH/Flashing Support
VIP
Retired
Messages
8,385
Reaction score
4,623
muffin_5-1_dt
muffin_5-2_dt
muffin_6-1_dt
muffin_6-2_dt
muffin_7-1_dt
muffin_7-2_dt


muffin_7-1_dt yesterday worked with this, so today decided to pack it and not working now..
Yeah 7-1 is the one that everyone usually uses.

Your soldering looks good, so there isn't really anything sticking out that I can see.
All I could recommend to do is touch up the points again. Even if you just touch them with the iron for a second, just give them all a quick re-do and see what happens.
 
K

Killjoy666

Getting There
Messages
1,649
Reaction score
234
muffin_5-1_dt
muffin_5-2_dt
muffin_6-1_dt
muffin_6-2_dt
muffin_7-1_dt
muffin_7-2_dt


muffin_7-1_dt yesterday worked with this, so today decided to pack it and not working now..
If You Have Stby_Clk Soldered (C Point) I Would Unsolder It And Enable The Oscillator.
 
S

smailer

Enthusiast
Messages
282
Reaction score
3
Yeah 7-1 is the one that everyone usually uses.

Your soldering looks good, so there isn't really anything sticking out that I can see.
All I could recommend to do is touch up the points again. Even if you just touch them with the iron for a second, just give them all a quick re-do and see what happens.
No luck, not booting. Strange why can hack it :smile: hundreds hacket but this one imposible :smile:
 
If You Have Stby_Clk Soldered (C Point) I Would Unsolder It And Enable The Oscillator.
can u explane more "oscillator" ?
 
K

Killjoy666

Getting There
Messages
1,649
Reaction score
234
No luck, not booting. Strange why can hack it :smile: hundreds hacket but this one imposible :smile:
 

can u explane more "oscillator" ?
Believe Everyone Cause It The “Crystal” But It’s Actually Called Oscillator.

You Have A Matrix V3 So It Comes With It You Probably Unsolder The 0ohm Jumper To Disable It. And Use The (C Point)
 
R

rynax

Enthusiast
Messages
178
Reaction score
12
use ace and try S-RGH instead of CR4 Muffin
 
N

Noobert

RGH/Flashing Support
VIP
Retired
Messages
8,385
Reaction score
4,623
No luck, not booting. Strange why can hack it :smile: hundreds hacket but this one imposible :smile:
 

can u explane more "oscillator" ?


See if unsoldering that one does anything.
 
N

Newsk

Getting There
Messages
2,497
Reaction score
329
Would double check stock is still booting since u said yesterday It was booting . Soldering looks good . I always use the onchip oscillator instead . Just rebrigdge the resistor you removed above e and f and unsolder c wire .
 
Top Bottom