What's new

Question RGH Jasper BB 512mb Help

M

max01

Newbie
Messages
25
Reaction score
0
Points
35
Sin$
7
Hello Everyone,

Need help with getting a jasper 512mb to glitcher with a coolrunner rev c. Can't get it to boot to xell, no matter which timing file i use..
Should i use rgh1, 1.2 or 2? and which wiring should i use. Will take some pic of the wiring.
I use the cables that come with the coolrunner.

I need the dvd key mainly, the original drive is damaged

this is the log from jr:
Version: 10
Flash Config: 0x00AA3020
00AA3020
Jasper 512MB
CB Version: 6750
* unpacking flash image, ....
Spare Data found, will remove.
Removed
* found decrypted CD
* found XeLL binary, must be linked to 0x1c000000
* we found the following parts:
SMC: 2.3
CB_A: 6750
CB_B: missing
CD (image): 8453
CD (decrypted): 8453
* this image will be valid *only* for: jasper (CB_6750)
* patching SMC...
Patching Jasper version 2.3 SMC at offset 0x12BA
* zero-pairing...
* constructing new image...
* encrypting CB...
* encrypting CD...
* base size: 70000
* No separate recovery Xell available!
* Flash Layout:
0x0..0x1FF (0x200 bytes) Header
0x200..0xFFF (0xE00 bytes) Padding
0x1000..0x3FFF (0x3000 bytes) SMC
0x4000..0x7FFF (0x4000 bytes) Keyvault
0x8000..0x11A3F (0x9A40 bytes) CB_A 6750
0x11A40..0x17A3F (0x6000 bytes) CD 8453
0x17A40..0xBFFFF (0xA85C0 bytes) Padding
0xC0000..0xFFFFF (0x40000 bytes) Xell (backup)
0x100000..0x13FFFF (0x40000 bytes) Xell (main)
* Encoding ECC...Done!
------------- Written into output\image_00000000.ecc
 
Z

Zerker24

Enthusiast
Messages
945
Reaction score
206
Points
170
Sin$
0
only getting 1 short and 1 long blink then off and repeat using the matrix..
doesn't matter which file i use..
You should only be getting a single blink from the rgh 1 files.

"J-runner/common/xsvf/jasper.xsvf"

Not sure what the difference between "jasper" and "jasper_en" is, so I guess see which one works best.
 
M

max01

Newbie
Messages
25
Reaction score
0
Points
35
Sin$
7
it look like something is wrong, before i used the cr chip , after i reflash stock flash ,console always boot up normal.. but now after i use the matrix chip, it wouldnt boot up even after flashing back the stock flash..
It just keep blinking green..
 
x86

x86

Enthusiast
Messages
269
Reaction score
20
Points
95
Sin$
0
Here is the connections
20190426_225255_zpsgtjlmbqg.jpg


20190426_225300_zpst0jqjafi.jpg


20190426_225331_zpscff8fr1a.jpg


20190426_225145_zpsjmvkbstm.jpg

 
wire route
20190426_225244_zpskjdrrrij.jpg

Your soldering is the issue. PLL, RST, and CLK wires are too long and the solder joints look cold.

Cut the wires and the ends need to be very short. Tin the wires and the solder points on the board. Use flux generously. Make sure that the tip of your soldering iron is narrow enough to fit between RST and PLL points.

Flash the original nand back to your console and then write the ecc image again to start from scratch.

Once your soldering is good, then your console will boot to xell with the righ timing file.
 
M

max01

Newbie
Messages
25
Reaction score
0
Points
35
Sin$
7
I got it to boot using jasper_en timing file, but it takes like 2 to 3min to boot to xell..

Can the diygadget's lite-on extractor addon (DB9 version) be used as a probe ?
 
Top Bottom
Login
Register