Solved RGH Dual Nand Wont boot "Orange power brick"

[HAWK zer0]

Ok, so my rgh was working perfectly fine no problems, etc... It came time to update the dash so I built an image with xebuild. I flashed the the nand on the demon and unplugged it for nearly 24hrs because at the moment I noticed xbl was down, therefore went to bed. I woke up today and tried to boot the console but I would only get a beep, the power brick light stayed solid orange with no change. It will not boot the Demon nor Retail Nand, but I can still read and write through the demon.

System:
Trinity
Demon Dual Nand
Slim Proto V2

I've tried a different power brick.
I've tried a different power outlet.
I've checked for bent pins.
I've removed the HDD
I've checked wiring
I've exchanged between 3 ROL Boards

 

[NETO0214]

Have u tried to reflash of nand?

 

[EliteSoldier001]

Yeah try reflashing it. Remake the image with xebuild and make sure there is no bad blocks.

 

[HAWK zer0]

yes I've tried.
I even unsoldered the 5v red wire on the glitch chip and flashed stock firmware on the demon side.
It doesn't even attempt to power on.
Fan doesn't spin, no green light for a sec, nothing as if it was completely dead.
Rather than the power brick light turning red, it remains orange.

 

[EliteSoldier001]

Maybe just a bad brick? Got any other 360 power bricks?

 

[HAWK zer0]

Honestly sounds like a south bridge problem to me but wouldn't it not allow me to read and write to the nand if it were so?

 

[EliteSoldier001]

If that's not it prolly broke that **** lol. That sucks tho. 
True. Yeah man it's just ****ed

 

[ShawnUnderSe7en]

So you can write the nand using the demon? If so try creating an older dash image and writing it. I doubt the console is broken given that it was working right before the update.

 

[EliteSoldier001]

Try putting dash launch and freestyle or whatever you use on a usb and boot that with Xell.

(This worked for me when I messed up some settings and flashed the wrong image and stuff.)

 

[HuskerHeaven]

He has to be leaving out a key price of info somewhere. What else were you doing? Flashing a demon nand will do nothing to the board, and even if it's a bad flash, will still power on.

 

[HAWK zer0]

Yes I can still write to the nand with the demon, I've made a stock retail image of the new dash for it as well as multiple glitched images of multiple dashboards.
It wont boot xell either.
Honestly theres nothing else to it, its exactly as I've described.
Its not even trying to boot, but its left me stumped because the power brick wont turn red or green for a sec.
Its as if it were completely dead, there must be something I could check.

 

[TheWeekendModder]

Write the ECC file appropriate for your console type to the demon nand, and see if you can even boot that.

 

[HuskerHeaven]

If it's not booting retail off the retail nand it won't boot anything. Was it apart when you updated.

 

[HAWK zer0]

If it's not booting retail off the retail nand it won't boot anything. Was it apart when you updated.

It was just missing the front faceplate.
It wont boot retail on the retail nand or through the demon nand.
I've disabled the glitch chip just to check the demon side as well.

 

[HAWK zer0]

The last time I remember seeing something like this is when someone intentionally blew all efuses!
I hope xebuild didn't screw me over here

 

[T H C]

It's most likely that you blew the fuses m9. Will you sell me the broken console?

 

[HuskerHeaven]

Quick question. Did you by chance pull the ground wire off the little demon board you put the usb in?

 

[HAWK zer0]

Not until I unmarried the board from the chasis.
No I wont sell the board lol

 

[HuskerHeaven]

Not looking to buy it. But a ungrounded board can cause it not too boot.

 

[HAWK zer0]

I meant the other guy asking to buy -__-
everything was perfectly grounded and wired and from my knowledge a bad ground would only cause the glitched image not to boot. I wont even boot retail