What's new

Solved RGH Corona 4GB

E

ejv

Enthusiast
Messages
60
Reaction score
0
Hello, i have Xbox 360 Slim E, MFR Date 2014-05-26, i think its Corona V6 4GB. I have Nand-X and JR Programmer v2, x360 ace v3. I have few qestions about it:
1. Do i need sd card reader/writer to read/write a nand ? Or can i do it just with nand-x/jr programmer ?
2. Do i need QSB kit?
3. Do i need to bridge R2C7 and R2C10 if resistorts are missing ?
4. Do i need solder Cpu Post Fix Adapter ? Or can i just attach it there.

Thanks for help.
 
N

Noobert

RGH/Flashing Support
VIP
Retired
Messages
8,385
Reaction score
4,630
Hello, i have Xbox 360 Slim E, MFR Date 2014-05-26, i think its Corona V6 4GB. I have Nand-X and JR Programmer v2, x360 ace v3. I have few qestions about it:
1. Do i need sd card reader/writer to read/write a nand ? Or can i do it just with nand-x/jr programmer ?
2. Do i need QSB kit?
3. Do i need to bridge R2C7 and R2C10 if resistorts are missing ?
4. Do i need solder Cpu Post Fix Adapter ? Or can i just attach it there.

Thanks for help.
  1. Corona v6 is a 4GB Nand, so yes, you need the SD Card reader/writer.
    The JR Programmer cannot handle reading or writing a 4GB Nand.
  2. You need a Postfix Adapter.
  3. Yes, only bridge them if the resistors are missing.
  4. It doesn't get solder, the little pin goes under the chip to touch the post out point.
 
E

ejv

Enthusiast
Messages
60
Reaction score
0
so every motherboard with 4GB need to be read/write with sd card reader/writer ?
 
E

ejv

Enthusiast
Messages
60
Reaction score
0
In this video, he is soldering two points. Do i need to do that ? Starts at 5:00
 
J

JoinTheResistance

Dead to the world, alive for the journey...
Messages
4,670
Reaction score
1,088
In this video, he is soldering two points. Do i need to do that ? Starts at 5:00
Those are just anchor points, I would recommend soldering them, but you can get way without it.
 
N

NerdyBits

Newbie
Messages
7
Reaction score
3
Make sure you get official gear though bud. I got a batch of cheap postfix adapters and it was the worst choice I ever made. Ended up throwing them out as they weren't made very well and barely touched the POST_OUT (if it even touched the right point at all)
 
E

ejv

Enthusiast
Messages
60
Reaction score
0
And how to bridge r2c6/r2c7/r2c10 ? Just with a tin ? or i need resistorts ?
 
N

Newsk

Contributor
Messages
2,513
Reaction score
331
just bridge them with solder. if you have trouble doing that u can use wire or a 0 ohm res. taken from another board or whatever or just solder e and f directly to bottom corresponding pad
0Cqtm4Vm.jpg
 
E

ejv

Enthusiast
Messages
60
Reaction score
0
4gb nand reader must be solder on MB permanently ? maximus or tx ? Or how to make homemade reader ?
 
Last edited:
E

ejv

Enthusiast
Messages
60
Reaction score
0
OT: What i have to set in Dashlaunch, when i wont go to System settings trough holding RB ?
 
N

Newsk

Contributor
Messages
2,513
Reaction score
331
Dashlaunch should be set by default to go to normal dash when holding rb . I've found that it sometimes won't work. U can go in Dashlaunch and try mapping another button to go to normal dash like rt for example ..what do u currently have your default boot set to now
 
E

ejv

Enthusiast
Messages
60
Reaction score
0
Hello. I have read a nand two times and i get error: 250 reading block 1a3. What its mean ?

.. but i found it at end and when i write nand with error: 202 writing block 1a3. What i should do now ?
 
Top Bottom