What's new

Tutorial RGH 1.2 Start to finish tutorial + how to get a CR4 like experience (Phats only)

  • Thread starter JoinTheResistance
  • Start date
  • Views 320,945
J

JoinTheResistance

Dead to the world, alive for the journey...
Messages
4,669
Reaction score
1,100
Points
1,045
Sin$
7
Hey guys!

I am trying to do this method on a jasper board with cr3 lite. What jumper settings should I use on the cr3? I dindn't find it in the tutorial. Many thanks.
Read this. Also, leave everything at S4 to OFF, and set S2 to bypass (1 and 5 ON, the rest OFF). After you've found the file that works best for you, play around with S2 and S4, ONE at a time!
 
S

Shane Edwards

Newbie
Messages
16
Reaction score
0
Points
35
Sin$
0
could you help with where the coolrunner chip solders to the qsb or is it the same as RGH1
 
J

JoinTheResistance

Dead to the world, alive for the journey...
Messages
4,669
Reaction score
1,100
Points
1,045
Sin$
7
could you help with where the coolrunner chip solders to the qsb or is it the same as RGH1
Only solder the 3V3, GND and CLK points onto the QSB, use my diagram for the rest.
 
PhoenixMods

PhoenixMods

Banned
Messages
79
Reaction score
26
Points
70
Sin$
0
This is a very well structured tutorial, I'll probably use some of this for reference in the future
 
RedEyedJesus

RedEyedJesus

✯UK Console Seller/Old Timer/Legend✯
Experienced Veteran Services Free Hoster
Messages
1,533
Reaction score
432
Points
355
Sin$
0
Thanks for this tut, really appreciate it. Just completed my first RGH1.2 install on a falcon & it insta boots! Will be using this in future phat installs thanks J JoinTheResistance P.s. CR Rev C, Left as standard (jp, cap & 1-2 etc left as is when out of packaging)
 
J

JoinTheResistance

Dead to the world, alive for the journey...
Messages
4,669
Reaction score
1,100
Points
1,045
Sin$
7
Thanks for this tut, really appreciate it. Just completed my first RGH1.2 install on a falcon & it insta boots! Will be using this in future phat installs thanks J JoinTheResistance P.s. CR Rev C, Left as standard (jp, cap & 1-2 etc left as is when out of packaging)
Thanks for sharing your results!
 
Green_Man

Green_Man

Getting There
Messages
1,119
Reaction score
396
Points
240
Sin$
0
followed this tutorial on a BB jasper with a coolrunner rev c, left the coolrunner as if it came out of the packaging and got instant boot, amazing tutorial :smile:
 
RedEyedJesus

RedEyedJesus

✯UK Console Seller/Old Timer/Legend✯
Experienced Veteran Services Free Hoster
Messages
1,533
Reaction score
432
Points
355
Sin$
0
Zephyr, every timing file, no boot at all :frown: Ah well
 
J

JoinTheResistance

Dead to the world, alive for the journey...
Messages
4,669
Reaction score
1,100
Points
1,045
Sin$
7
I think Taiwan, tried everything. I knew it was a long shot before i started the install. Xenon next i think :smile:
Zephyrs with Taiwanese CPUs don't work well with RGH2 and RGH1.2, but you can try R-JTAG or R-JTOP.
Btw, your Xenon MUST have a CPU made in Canada, otherwise the only thing you can do is use the TTL version of RGH1.2 to get the CPU and DVD keys, but no Xell and no dash.
 
RedEyedJesus

RedEyedJesus

✯UK Console Seller/Old Timer/Legend✯
Experienced Veteran Services Free Hoster
Messages
1,533
Reaction score
432
Points
355
Sin$
0
Zephyrs with Taiwanese CPUs don't work well with RGH2 and RGH1.2, but you can try R-JTAG or R-JTOP.
Btw, your Xenon MUST have a CPU made in Canada, otherwise the only thing you can do is use the TTL version of RGH1.2 to get the CPU and DVD keys, but no Xell and no dash.

How do i tell between a canadian/Taiwan CPU? TTL?
 
J

JoinTheResistance

Dead to the world, alive for the journey...
Messages
4,669
Reaction score
1,100
Points
1,045
Sin$
7
How do i tell between a canadian/Taiwan CPU? TTL?
There you go:
image.jpg

Btw, the second picture is from a Falcon/Jasper CPU, which has smaller die than your Xenon/Zephyr CPU.
TTL
Keep in mind that you'll need a USB TTL converter or a COM level sniffer.
 
RedEyedJesus

RedEyedJesus

✯UK Console Seller/Old Timer/Legend✯
Experienced Veteran Services Free Hoster
Messages
1,533
Reaction score
432
Points
355
Sin$
0
There you go:
image.jpg

Btw, the second picture is from a Falcon/Jasper CPU, which has smaller die than your Xenon/Zephyr CPU.
TTL
Keep in mind that you'll need a USB TTL converter or a COM level sniffer.

Thanks man
 
W

Witalka

Enthusiast
Messages
6
Reaction score
1
Points
55
Sin$
7
Hey :smile: , first thank you for this tut, i get my nand without badblocks.
I cant get my Xell boot to get the Key, i dont know if the problem my soldering or other things.
I get the wire as short as i can.. but no xell booting, i hear a fan reboot but nothing happens.. the xbox 360 jasper 256 (have no drive) start without the ecc and CL Rev C.

CL Rev C : JP & 3-2 Closed , CAP tryes open & closed
Ground goes to AV Port

Code:
http://www.directupload.net/file/d/4184/ive3sgnx_jpg.htm
http://www.directupload.net/file/d/4184/8kidf2p5_jpg.htm
http://www.directupload.net/file/d/4184/495ha2iy_jpg.htm
http://www.directupload.net/file/d/4184/xrw7apdk_jpg.htm
http://www.directupload.net/file/d/4184/8ktjoq9s_jpg.htm

Sry 4 bad englisch (german) :smile:

edit: tryed many timing files :/ and re soldering all my points..
edit2: or should i make a Support thread for my problem ? :biggrin:
 
Last edited:
J

JoinTheResistance

Dead to the world, alive for the journey...
Messages
4,669
Reaction score
1,100
Points
1,045
Sin$
7
Hey :smile: , first thank you for this tut, i get my nand without badblocks.
I cant get my Xell boot to get the Key, i dont know if the problem my soldering or other things.
I get the wire as short as i can.. but no xell booting, i hear a fan reboot but nothing happens.. the xbox 360 jasper 256 (have no drive) start without the ecc and CL Rev C.

CL Rev C : JP & 3-2 Closed , CAP tryes open & closed
Ground goes to AV Port

Code:
http://www.directupload.net/file/d/4184/ive3sgnx_jpg.htm
http://www.directupload.net/file/d/4184/8kidf2p5_jpg.htm
http://www.directupload.net/file/d/4184/495ha2iy_jpg.htm
http://www.directupload.net/file/d/4184/xrw7apdk_jpg.htm
http://www.directupload.net/file/d/4184/8ktjoq9s_jpg.htm

Sry 4 bad englisch (german) :smile:

edit: tryed many timing files :/ and re soldering all my points..
edit2: or should i make a Support thread for my problem ? :biggrin:
Does the debug LED blink every few seconds? Also take a look at this:
1) short blink -> short -> short
———##————##———##———
this behavior means, glitch was successful, but xbox have failed to start. that usually means, the pulse length (L) was too long, or the timing value (T) was too small. If you always get the 'short' cycles, decrease the length (L).

2) short blink -> short -> long
———##————##———######
this one means checks failure. too short length (L) or too high timing value (T). try the file with longer length (L) and lower timing (T).

3) fast long blinks ONLY (no short ones) on phat (Falcon commonly) - southbridge problem. replug the xbox power and try again. no idea wtf, maybe that's caused by too long pulse (try to use shorter L?). also using ALT_RST might help. cr4 ECC can partially fix this issue
And this:
*This wasn't made for RGH1.2, but the debug LED blinking patterns are the same.
If you can't achieve success, to understand what's wrong, you should follow the LED blinking explanation below:
1) LED blinks two times SHORT, then SHORT:
.....##...##...................##............
this behaviour means all checks were passed, but console have failed to start.
commonly happens when the pulse length is too large, or the timing value is too low

2) LED blinks two times SHORT, then LONG:
.....##...##...................##############
this one means checks failure. Too large timing, or too short pulse length

for example, with TR_L_0.2_T_59.7 you must get only LONG cycles, and with TR_L_0.9_T_59.7 you'll get only SHORT cycles
BUT with both TR_L_0.2_T_60.9 and TR_L_0.9_T_60.9 you'll get mostly LONG cycles.

the ideal length is on the edge of LONG / SHORT behaviour
but the ideal timing is a bit below that edge for timing values.

for example, I get mostly SHORT cycles with TR_L_0.8_T_59.7, but TR_L_0.6_T_59.7 and TR_L_0.5_T_59.7 gives both of them
then, I get mostly SHORT cycles with TR_L_0.8_T_60.6, and TR_L_0.8_T_60.9 gives me both of them
so the edges for me are 60.9 timing and 0.6 length. But an ideal timing I found is 60.6 / 0.6 !!!
That's what I meant by 'a bit below the edge'

I hope you got the idea how to find the timing without bruteforcing them all -_-

Let's continue the description of LED behaviour, there're two more cases:


3) LED blinks four times SHORT, then LONG:
.....##...##...................##...##...................##############
the pulse length is very big. maybe you use large length with the alt rst point on phats
4) LED isn't blinking at all, or always ON
something wrong with your wiring. re-check everything
 
W

Witalka

Enthusiast
Messages
6
Reaction score
1
Points
55
Sin$
7
thats you know its my first xbox 360 to rgh i get they as a gift.
i readed many tut in englisch and german and viewed this video
Code:
https://www.youtube.com/watch?v=gZBCXSFBiDM
for understanding.

i followd your tut step by step to rgh my xbox360 (jasper 256)

Yes the Debug led is on :wink:,

i would say its "short blink -> short -> long".

Video:
Code:
http://sendvid.com/y5fqd8bi

ps. I resoldering some points with Kynar wire 30 awg (saw some thread thats use kynar wire and i had good experience with NEW 3DS Nand mod soldering)

Pics
Code:
http://www.directupload.net/file/d/4185/rvu5x33q_jpg.htm
http://www.directupload.net/file/d/4185/8hd24g4z_jpg.htm
http://www.directupload.net/file/d/4185/6dype3xs_jpg.htm
http://www.directupload.net/file/d/4185/kixpyrwb_jpg.htm
http://www.directupload.net/file/d/4185/i5fvofua_jpg.htm
http://www.directupload.net/file/d/4185/if7gti5l_jpg.htm
 
Last edited:
J

JoinTheResistance

Dead to the world, alive for the journey...
Messages
4,669
Reaction score
1,100
Points
1,045
Sin$
7
thats you know its my first xbox 360 to rgh i get they as a gift.
i readed many tut in englisch and german and viewed this video
Code:
https://www.youtube.com/watch?v=gZBCXSFBiDM
for understanding.

i followd your tut step by step to rgh my xbox360 (jasper 256)

Yes the Debug led is on :wink:,

i would say its "short blink -> short -> long".

Video:
Code:
http://sendvid.com/y5fqd8bi

ps. I resoldering some points with Kynar wire 30 awg (saw some thread thats use kynar wire and i had good experience with NEW 3DS Nand mod soldering)

Pics
Code:
http://www.directupload.net/file/d/4185/rvu5x33q_jpg.htm
http://www.directupload.net/file/d/4185/8hd24g4z_jpg.htm
http://www.directupload.net/file/d/4185/6dype3xs_jpg.htm
http://www.directupload.net/file/d/4185/kixpyrwb_jpg.htm
http://www.directupload.net/file/d/4185/i5fvofua_jpg.htm
http://www.directupload.net/file/d/4185/if7gti5l_jpg.htm
Is it short -- short -- long, with all of the timing files?
 
Top Bottom
Login
Register