What's new

Tutorial How to RGH slim/Phat

  • Thread starter FLeX Gam3s
  • Start date
  • Views 9,582
FLeX Gam3s

FLeX Gam3s

Enthusiast
Messages
453
Reaction score
10
Points
70
Sin$
0
This PDF found here

Hardware requirements
xecuter coolrunner

NAND-X

NAND-X to coolrunner programing cable
Software requirements

1. Jrunner

Xbox requirements
1. A xbox Phat of any motherboard type or a Slim trinity

2. A console at or bellow 2.0.14699.0 kernel

Step 1
Dumping the Nand

Before doing anything make sure your xbox is updated to the 2.0.14699.0 dashboard

slim this does not matter
install your Nand-x using the diagrams shown

PHAT
Wire_Solder_0526.jpg


SLIM

nandx_slim.jpg


Once you have installed your nand-x plug your console into you power supply but do not turn the console on then plug the nand-x cable you soldered to the mother board into the nand-x and the usb cable into the computer then open up Jrunner.
once open click this box

jrunnerbox.png


After clicking this box a window will pop up with a list of different console types. Select what type of motherboard your console has after doing so click the read Nand box shown here
readnand.png

Jrunner will then proceed to dump your nand twice and then compare the nands to make sure they match if they do continue on. if the nands dont match check your soldering and try again if you cant get your nands to match after MULTIPLE times of trying then ask for help in the support forums

1.1 For Phats only checking the CB

to do this on the right had side of the Jrunner app you will see a bunch of box's with writing in look at the box labeled "2BL[CB]" shown here

24468825.png

if your CB version dose not match the ones listed than do not continue

Falcon and Opus 5771

Zephyr 4578 or 4579

Jasper 6750 or 6751

if your CB is correct than continue if not the you console is not exploitable at this stage and you will have to wait till RGH 2.0!


2. Programing your Xecuter coolrunner

to do this plug the coolrunner into the nand x like so
nandx_coolrunner_cable.jpg

then click the Flash Coolrunner box shown here

flashcoolrunner.png

it will then program your coolrunner

once finished unplug your coolrunner

Step 3 installing your Coolrunner

To do so follow one of these diagrams depending on your mother board type

phat_install_wires.jpg



phat_xenon.jpg


slim_install_wires.jpg


Step 4 creating and writingn your .ECC (xell)
to do this simply click the Create ECC box shown here

createecc.png

it will then create your .ecc file

once done with you nand-x hooked you press the write ECC box shown here

writeecc.png

it will then write the .ecc file you created to your console

Step 5 Getting you cpu key

unplug you nand-x from the console and plug you xbox into the tv and turn it on make sure you have a camera handy to take a photo of you cpu key at this
point

imag0015yu.jpg


open notepad and type out fuse set 3 and then add fuse set 5 to the end of it and open a notepad and type it in then save it as cpukey.txt
(Example: if my fuse set 3 is 012356789ABCDEF and my fuse set 5 is ABCDEF012356789 than my cpu key would be 012356789ABCDEFABCDEF012356789)

step 6 Building and writing you ggbuild image

to do this put your cpu key in the cpu key box shown here

cpubh.png

click dash version box shown here

dashzd.png

a tab will appear with a list of dash versions i suggest picking 14719 as it is the newest then click create image Jrunner will then make your image when has finished click the write image box i will then write ggbuild once it has finished unplug your nand-x from the console then remove the power cable for 30 sec or more then plug back in and boot

Step 7

Have fun with your new RGH xbox 360

i take no credit for this but i did take the time to edit the text with spelling errors
 
OG_NAME_IS_OG

OhGnomez

Enthusiast
Messages
63
Reaction score
9
Points
55
Sin$
7
Why isnt there a RGH tut stickied?

JTAGable xboxs are getting rarer, so they need the RGH to be stickied
 
Top Bottom
Login
Register