Solved Falcon CoolRunner rev c help RGH 1.2

Discussion in 'Xbox 360 Support' started by stegzy, Jan 20, 2017 with 52 replies and 3,915 views.

LED problem coolrunner rev c

  1. rev c help

    0 vote(s)
    0.0%
  2. --------

    0 vote(s)
    0.0%
  1. stegzy

    stegzy Enthusiast

    Messages:
    106
    Ratings:
    8
    I got to boot into my rgh dashboard once now when i boot up my console the L.E.D turns green then starts to blink after 5 seconds then goes back to solid for 5 seconds then blinks in a infinte loop im not seeming to get any successful boots :frown:
    Thanks For Help
     
  2. Noobert

    Noobert RGH/Flashing Support VIP Retired

    Messages:
    8,314
    Ratings:
    4,358
    Did you solder it yourself? Or did you buy it?
     
  3. OP
    stegzy

    stegzy Enthusiast

    Messages:
    106
    Ratings:
    8
    myself did it all today :smile:
     
  4. Noobert

    Noobert RGH/Flashing Support VIP Retired

    Messages:
    8,314
    Ratings:
    4,358
    Are you able to upload some pictures of your soldering to Imgur and link them here?
     
  5. OP
    stegzy

    stegzy Enthusiast

    Messages:
    106
    Ratings:
    8
    2 secs
     
    Last edited: Jan 20, 2017
  6. OP
    stegzy

    stegzy Enthusiast

    Messages:
    106
    Ratings:
    8
    soz it took a bit and theyre not the best quality pics







     
    Last edited: Jan 20, 2017
  7. Newsk

    Newsk Getting There

    Messages:
    2,470
    Ratings:
    315
    so is it rgh 1 or something? cause rgh 1.2 would have the chip pulsing rather than on solid. Is it a jasper? if so did you try bridging cap pad? also pll bypass looks a little sketchy may need to touch that point up .

    so need to know a bit more in order to suggest anything else like timing files ect.
     
  8. Killjoy666

    Killjoy666 Getting There

    Messages:
    1,649
    Ratings:
    227
    Your CPU_RST Wire Is Touching The Coil, Could Be A Issue Of It Not Booting.
     
  9. OP
    stegzy

    stegzy Enthusiast

    Messages:
    106
    Ratings:
    8
    it just pulses then solid then pulses then solid then pulses
     
  10. OP
    stegzy

    stegzy Enthusiast

    Messages:
    106
    Ratings:
    8
  11. Newsk

    Newsk Getting There

    Messages:
    2,470
    Ratings:
    315
    What timing file is on it ?

    Did you select glitch 2 when u created your ecc?
     
  12. OP
    stegzy

    stegzy Enthusiast

    Messages:
    106
    Ratings:
    8
    yes and im using the 15432 timing files if_u_mad timing file 21 in the matrix section and ive tried many more timing files and i have selected glitch 2
     
  13. Newsk

    Newsk Getting There

    Messages:
    2,470
    Ratings:
    315
    Ok well what dash was console on when u read nand. And sorry if u already answered this but what motherboard is it ?
     
  14. OP
    stegzy

    stegzy Enthusiast

    Messages:
    106
    Ratings:
    8
    falcon and ik it sounds retarded but i forgot to check the dash version XD
     
  15. Newsk

    Newsk Getting There

    Messages:
    2,470
    Ratings:
    315
    That's easy load up nand dump and see what jrunner says[DOUBLEPOST=1485018971][/DOUBLEPOST]The reason I'm asking is I want to be sure it's not a rgh 1 dash
     
  16. OP
    stegzy

    stegzy Enthusiast

    Messages:
    106
    Ratings:
    8
    where about does it because ive just loaded it up :smile:
     
  17. Newsk

    Newsk Getting There

    Messages:
    2,470
    Ratings:
    315
    Over towards the right in the nand info or one of those tabs it will have the dash and cb
     
  18. OP
    stegzy

    stegzy Enthusiast

    Messages:
    106
    Ratings:
    8
    i can see CB_A and CB_B?[DOUBLEPOST=1485019402][/DOUBLEPOST]
    i can see CB_A and CB_B?
     
  19. Newsk

    Newsk Getting There

    Messages:
    2,470
    Ratings:
    315
    . What numbers do all those say ? U can take a pic if u want and link it
     
  20. OP
    stegzy

    stegzy Enthusiast

    Messages:
    106
    Ratings:
    8
     

Share This Page