What's new

Tutorial [DIY tutorial] Matrix SPI nand flasher upgrade to CPLD (coolrunner/glitch chip) programmer

  • Thread starter JoinTheResistance
  • Start date
  • Views 138,006
J

JoinTheResistance

Dead to the world, alive for the journey...
Messages
4,670
Reaction score
1,094
After i´ve made the conversion of the Matrix SPI to this Nand$coolrunnerflasher, i´m not being able to use it as a nand programer.
The AutoGG software does not reconize it. What can I do? I need to flash the nand again
Have you tried Jrunner?
it Will only work for nand reading and writing through Jrunner? Becouse i´m not beeing able to open the Jrunner, couse it says a Connection Error and crashes. Can someone help?
Disable your internet connection, open Jrunner, wait 10 seconds and enable it again.
 
M

Madeinpavao

Newbie
Messages
8
Reaction score
0
Have you tried Jrunner?

Disable your internet connection, open Jrunner, wait 10 seconds and enable it again.




Jrunner stop crashing, but when I try to Write Xellreloaded give this message:
Version: 01
Flash Config: 0x00000000
Can not Continue
 
Last edited:
J

JoinTheResistance

Dead to the world, alive for the journey...
Messages
4,670
Reaction score
1,094
Jrunner stop crashing, but when I try to Write Xellreloaded give this message:
Version: 01
Flash Config: 0x00000000
Can not Continue
Then you probably did something wrong when modding the matrix. Can you post a picture of the modded matrix nand flasher?
 
M

Madeinpavao

Newbie
Messages
8
Reaction score
0
Then you probably did something wrong when modding the matrix. Can you post a picture of the modded matrix nand flasher?
Becouse of what you said, i´ve figured that I had removed the alterations on the matrix board, and that´s why it was not working.
Now i have another issue. My glitcher it´s the matrix v1, my xbox 360 looks like a jasper, but it´s original NAND file shows it´s a Falcon. I want to know wich version of the RGH should I program my Matrix V1 Glticher? if it is 1.2, wich version of it (becouse there´s a lot of it)?
 
J

JoinTheResistance

Dead to the world, alive for the journey...
Messages
4,670
Reaction score
1,094
Becouse of what you said, i´ve figured that I had removed the alterations on the matrix board, and that´s why it was not working.
Now i have another issue. My glitcher it´s the matrix v1, my xbox 360 looks like a jasper, but it´s original NAND file shows it´s a Falcon. I want to know wich version of the RGH should I program my Matrix V1 Glticher? if it is 1.2, wich version of it (becouse there´s a lot of it)?
Can you post a picture of the power socket on the back of the board? As for the timing files, RGH1.2 ones are the same for all consoles, just find one that works for yours! :wink:
 
M

Madeinpavao

Newbie
Messages
8
Reaction score
0
Can you post a picture of the power socket on the back of the board? As for the timing files, RGH1.2 ones are the same for all consoles, just find one that works for yours! :wink:

Thank´s for the help. And not trying to be abusive with you helping. I´m posting also a picture off something that i´ve screw up. The C spot on the xbox board, i´ve puled whitout noticing, and the component that was before it got lost. Now the xbox only turn on, but does not boot, when the Matrix Glitcher is installed. What can I do in that case? Rather not have to send to anyone to fix, becouse isn´t much worth the price.
https://ibb.co/dcubXm
https://ibb.co/b90TdR
dcubXm

b90TdR

dcubXm

b90TdR
 
J

JoinTheResistance

Dead to the world, alive for the journey...
Messages
4,670
Reaction score
1,094
Thank´s for the help. And not trying to be abusive with you helping. I´m posting also a picture off something that i´ve screw up. The C spot on the xbox board, i´ve puled whitout noticing, and the component that was before it got lost. Now the xbox only turn on, but does not boot, when the Matrix Glitcher is installed. What can I do in that case? Rather not have to send to anyone to fix, becouse isn´t much worth the price.
https://ibb.co/dcubXm
https://ibb.co/b90TdR
dcubXm

b90TdR

dcubXm

b90TdR
Seems like the top plastic in the power socket is missing, so I can't tell what motherboard revision it is. Can you post a picture of the top side of the board.
 
M

Madeinpavao

Newbie
Messages
8
Reaction score
0
I had created the ECC file with RGH in Jrunner and wrouted on the xbox, and i´m trying the RGH 1.2 files on the Matrix Glitcher, but i´ve tried almost all off them and until now all I get is a blinking green light on the xbox and a blinking blue light in the Matrix, but I can Let it blinking for almost 100 minutes and no booting.

https://ibb.co/ghjWF6
https://ibb.co/f5zRhm
https://ibb.co/nLAXNm
https://ibb.co/ccHwhm
https://ibb.co/fBAGhm
https://ibb.co/jJPbhm
https://ibb.co/bGmiTR
https://ibb.co/dwJ8v6 
Seems like the top plastic in the power socket is missing, so I can't tell what motherboard revision it is. Can you post a picture of the top side of the board.

I had created the ECC file with RGH in Jrunner and wrouted on the xbox, and i´m trying the RGH 1.2 files on the Matrix Glitcher, but i´ve tried almost all off them and until now all I get is a blinking green light on the xbox and a blinking blue light in the Matrix, but I can Let it blinking for almost 100 minutes and no booting.

https://ibb.co/ghjWF6
https://ibb.co/f5zRhm
https://ibb.co/nLAXNm
https://ibb.co/ccHwhm
https://ibb.co/fBAGhm
https://ibb.co/jJPbhm
https://ibb.co/bGmiTR
https://ibb.co/dwJ8v6
 
J

JoinTheResistance

Dead to the world, alive for the journey...
Messages
4,670
Reaction score
1,094
I had created the ECC file with RGH in Jrunner and wrouted on the xbox, and i´m trying the RGH 1.2 files on the Matrix Glitcher, but i´ve tried almost all off them and until now all I get is a blinking green light on the xbox and a blinking blue light in the Matrix, but I can Let it blinking for almost 100 minutes and no booting.

https://ibb.co/ghjWF6
https://ibb.co/f5zRhm
https://ibb.co/nLAXNm
https://ibb.co/ccHwhm
https://ibb.co/fBAGhm
https://ibb.co/jJPbhm
https://ibb.co/bGmiTR
https://ibb.co/dwJ8v6 


I had created the ECC file with RGH in Jrunner and wrouted on the xbox, and i´m trying the RGH 1.2 files on the Matrix Glitcher, but i´ve tried almost all off them and until now all I get is a blinking green light on the xbox and a blinking blue light in the Matrix, but I can Let it blinking for almost 100 minutes and no booting.

https://ibb.co/ghjWF6
https://ibb.co/f5zRhm
https://ibb.co/nLAXNm
https://ibb.co/ccHwhm
https://ibb.co/fBAGhm
https://ibb.co/jJPbhm
https://ibb.co/bGmiTR
https://ibb.co/dwJ8v6
Why do you have a capacitor on the C point? Also, it's a Falcon.
I would suggest that you open a new thread in the Xbox 360 support section, we are getting way of topic on this one.
 
bobthecooldad

bobthecooldad

Newbie
Messages
2
Reaction score
0
sorry i am stuck at the end.. the console doesnt do anything if i try to turn it on (with the cool runner installed and the matrix un soldered).. i thought it might be as my ecc didnt flash (i dont know i saw someone say it is a normal error with these and it had).. now when i plug it into the pc and restored the matrix nand flasher i get this error
Version: 01
Flash Config: 0x00000000
Can not Continue

However i have not changed any wiring and i have checked all the connections
 
Last edited:
Z

Zsolt Kallai

Newbie
Messages
5
Reaction score
0
Hello! I have problem. A want flash my x360 ace v3 with matrix nand flasher, i build the modification, install the driver but i get this error:
Opening XSVF File ........... [OK]
Libusb DLL Version .......... [0.1.12.1]
Accessing USB Device ........ [ERROR]

Somebody knwo how can i fix it?
 
hamsternufc

hamsternufc

Newbie
Messages
2
Reaction score
0
Hello! I have problem. A want flash my x360 ace v3 with matrix nand flasher, i build the modification, install the driver but i get this error:
Opening XSVF File ........... [OK]
Libusb DLL Version .......... [0.1.12.1]
Accessing USB Device ........ [ERROR]

Somebody knwo how can i fix it?
Change usb lead. I used one that had the little black power block...I.e a camera usb. Worked first time after changing usb. !!!
 
Z

Zsolt Kallai

Newbie
Messages
5
Reaction score
0
yes its work thank you but now i hav other problem.

Opening XSVF File ........... [OK]
Libusb DLL Version .......... [1.2.5.0]
Accessing USB Device ........ [OK]
Xilinx XC2C32A .............. [NOT DETECTED]
Xilinx XC2C64A .............. [NOT DETECTED]

i would like flash only the timing and i am ready, but i cant beacuse i get this error. i try before with j runner, but this write to me "wrong arm version"
 
E

EvkaX155

Newbie
Messages
7
Reaction score
3
yes its work thank you but now i hav other problem.

Opening XSVF File ........... [OK]
Libusb DLL Version .......... [1.2.5.0]
Accessing USB Device ........ [OK]
Xilinx XC2C32A .............. [NOT DETECTED]
Xilinx XC2C64A .............. [NOT DETECTED]

i would like flash only the timing and i am ready, but i cant beacuse i get this error. i try before with j runner, but this write to me "wrong arm version"


You can't program x360ace chips with the matrix flasher, unfortunately. You need a J-R programmer for that, look up on ebay, they aren't terribly expensive. Or just use Matrix chips, they achieve the exact same thing and cost a bit less. :smile:
 
rynax

rynax

Enthusiast
Messages
178
Reaction score
13
Thanks for the great guide and the easy to use XSVF Gui.
Just wonder in the PICFLASH_XSVF.HEX firmware build if there's PIC Pins used for LED to indicate read/write activities?
Or maybe there's source code for it available?

Cheers,

W
 
S

sony5

Newbie
Messages
12
Reaction score
0
yes its work thank you but now i hav other problem.

Opening XSVF File ........... [OK]
Libusb DLL Version .......... [1.2.5.0]
Accessing USB Device ........ [OK]
Xilinx XC2C32A .............. [NOT DETECTED]
Xilinx XC2C64A .............. [NOT DETECTED]

i would like flash only the timing and i am ready, but i cant beacuse i get this error. i try before with j runner, but this write to me "wrong arm version"

make sure your glitch cheap isnt connected to the vcc if you rgh wires are installed already and your using a matrix v1
 
rynax

rynax

Enthusiast
Messages
178
Reaction score
13
Actually on the original thread of this mod, the author freelancer has made a modified version and it can program the XC2C128 (360ACE V3) now.
See reply #88 #89 #90
Google Title:
Regalino per la comunity di Console Open: Usb Spi flasher fatto su Eagle. UPDATE V2.1
 
Last edited:
F

FJeff

Newbie
Messages
1
Reaction score
0
I'm getting Accessing USB Device ........ [ERROR]

I already tried switching USB cables and it didn't help.
 
Top Bottom