What's new

Solved Coolrunner rev d is not glitching

  • Thread starter juthegame
  • Start date
  • Views 957
J

juthegame

Newbie
Messages
89
Reaction score
1
Working on a corona which has three resistors missing which I bridged and these resistors are r2c7,r2c6 and r2c10.the post trace is missing but I installed the post trace adapter v2,which i tried all the points from 120,90,70,50 nd 5 but the coolrunner wouldn't glitch but the red light is on.I read the nand are the same,created ecc and write eccentric no bad blocks try to get cpu Key Not glitching
 
Last edited:
N

Newsk

Getting There
Messages
2,497
Reaction score
329
Need to see some pics of the install ofcoarse . Also test your postfix is making connection by testing resistance to ground (k ohms) on any of the postfix pads. Any motherboard ground will do including metal casing above av port .
 
J

juthegame

Newbie
Messages
89
Reaction score
1
I changed the post fix adapter and unbridged the r2c7,r2c6 where there are missing the resistors and I connected the wires from the coolrunner which are e and f direct on r2c7 nd r2c6,now am having the following troubles
1)the green light is flashing but no glitch sound.
2)its not booting
3)fun starts to spin normally nd after sometimes it spins faster the following happens
- the green light stops flashing on coolrunner at some point
- sometimes the green light on the switch button turns red and starts to flash red
-when the fun spins faster at some point it will try to get back to normal and shuts off the console.
I will post pics later.thanks
 
K

Killjoy666

Getting There
Messages
1,649
Reaction score
234
I changed the post fix adapter and unbridged the r2c7,r2c6 where there are missing the resistors and I connected the wires from the coolrunner which are e and f direct on r2c7 nd r2c6,now am having the following troubles
1)the green light is flashing but no glitch sound.
2)its not booting
3)fun starts to spin normally nd after sometimes it spins faster the following happens
- the green light stops flashing on coolrunner at some point
- sometimes the green light on the switch button turns red and starts to flash red
-when the fun spins faster at some point it will try to get back to normal and shuts off the console.
I will post pics later.thanks
Best Thing I Suggest Is Using Project Muffin When Using A Coolrunner
 
J

juthegame

Newbie
Messages
89
Reaction score
1
Where can I downloaded Project Muffin files
 
Last edited:
J

juthegame

Newbie
Messages
89
Reaction score
1
Is there any alternatives underneath the board for e and f,nd can I flash it back to stock nand and works
 
N

Newsk

Getting There
Messages
2,497
Reaction score
329
There are but they are tiny points . Check the image in my signature for the points .

But like mentioned earlier just switch to muffin install and u won't even need e /f
 
J

juthegame

Newbie
Messages
89
Reaction score
1
Is it the correct installation for the muffin install and can I use the files from rgh12.
 
The green wire is on f on the coolrunner
 
N

Newsk

Getting There
Messages
2,497
Reaction score
329


Here's for matrix . Can't find my picture for rev d but 3.3v and ground , then c is post d is cpu rst. And e is db2g3.
You need to use the muffin timings specifically and make image with cr4 ticked .try with switch on phat first , leave other jumpers alone
 
J

juthegame

Newbie
Messages
89
Reaction score
1
I have been searching for the muffin timing files but can't find where to download them .thanks
 
J

juthegame

Newbie
Messages
89
Reaction score
1
For the cr4 I need to read the nand again because the cr4 was not ticked
 
N

Newsk

Getting There
Messages
2,497
Reaction score
329
No just take your nand read and recreate ecc, or image with it ticked
 
K

Killjoy666

Getting There
Messages
1,649
Reaction score
234
Trinity Is 7-1, Corona Is 3-1.

Other Files Don’t Work, Well Never Have For Me.
 
J

juthegame

Newbie
Messages
89
Reaction score
1
I have tried 3-1
 
Could it be that wires for d and e are too long
 
Top Bottom