505_
"Milkshake?"
Update: This is a Halo 2 Vista tutorial. Not Halo 2 for the original xbox.
Items needed:
Assembly
Halo 2
---------------------
Step 1: Open up a map,
---------------------
Step 2:
Open both Halo 2 and Assembly.
---------------------
Step 3:
Start a mission, pick any. I picked number 4.
---------------------
Step 4:
After opening the map in Halo, open it in assembly.
---------------------
Step 5:
In assembly, go to the bipd section.
Here we can change all types of things.
Colors, Jump Height, No fall damage.
---------------------
Step 6:
Changing colors:
Go to the bipd section , and pick either dervish(arbiter) or Master-chief.
Change the two colors to anything. Then go the top with Change colors you see a 0 - 3 (4)
Change it to 1 - 3 (4).
Then change the colors of that one to the same colors.
Then click poke.
( change colors )
---------------------
Step 7:
Change Weapon aim Assist:
Go onto the list, and go down to the bottom. There you will find weap.
Click it, and pick any weapon.
After clicking the weapon go down until you see aim-assist or auto-aim angle.
Change the value of Auto-aim angle to a number higher than it already is, same goes for auto-aim range.
Value Range:
0-10 short range aim-assist
10-20 medium range aim-assist
20-40 long range aim-assist
100-300 Insane Range aim-assist
---------------------------
Step 8:
Bipd Changing, and Stats:
Go to the bipd section again, and pick either dervish(arbiter) or Master-chief.
After picking one, change the model, and material effects.
You could also change predicted Resource to the model you want as well.
( make sure to poke )
---------------------------
Step 9:
Jump height:
go all way down the meta editor list, until you see bipd. You should see items such as Jump velocity, or Moving turn speed.
Change the value of Jump velocity to one of the following.
normal jump range: 3-5
Medium Jump range: 5-7
High jump range: 7-15
If you want no fall damage, click flags, then immune to fall damage.
Then click poke.
---------------------------
Finished!
Items needed:
Assembly
Halo 2
---------------------
Step 1: Open up a map,
1. 00a_introduction
2. 01a_tutorial
3. 01b_spacestation
4. 03a_oldmombasa
5. 03b_newmombasa
6. 04a_gasgiant
7. 04b_floodlab
8. 05a_deltaapproach
9. 05b_deltatowers
10. 06a_sentinelwalls
11. 06b_floodzone
12. 07a_highcharity
13. 07b_forerunnership
14. 08a_deltacliffs
15. 08b_deltacontrol
2. 01a_tutorial
3. 01b_spacestation
4. 03a_oldmombasa
5. 03b_newmombasa
6. 04a_gasgiant
7. 04b_floodlab
8. 05a_deltaapproach
9. 05b_deltatowers
10. 06a_sentinelwalls
11. 06b_floodzone
12. 07a_highcharity
13. 07b_forerunnership
14. 08a_deltacliffs
15. 08b_deltacontrol
Step 2:
Open both Halo 2 and Assembly.
---------------------
Step 3:
Start a mission, pick any. I picked number 4.
---------------------
Step 4:
After opening the map in Halo, open it in assembly.
---------------------
Step 5:
In assembly, go to the bipd section.
Here we can change all types of things.
Colors, Jump Height, No fall damage.
---------------------
Step 6:
Changing colors:
Go to the bipd section , and pick either dervish(arbiter) or Master-chief.
Change the two colors to anything. Then go the top with Change colors you see a 0 - 3 (4)
Change it to 1 - 3 (4).
Then change the colors of that one to the same colors.
Then click poke.
( change colors )
---------------------
Step 7:
Change Weapon aim Assist:
Go onto the list, and go down to the bottom. There you will find weap.
Click it, and pick any weapon.
After clicking the weapon go down until you see aim-assist or auto-aim angle.
Change the value of Auto-aim angle to a number higher than it already is, same goes for auto-aim range.
Value Range:
0-10 short range aim-assist
10-20 medium range aim-assist
20-40 long range aim-assist
100-300 Insane Range aim-assist
---------------------------
Step 8:
Bipd Changing, and Stats:
Go to the bipd section again, and pick either dervish(arbiter) or Master-chief.
After picking one, change the model, and material effects.
You could also change predicted Resource to the model you want as well.
( make sure to poke )
---------------------------
Step 9:
Jump height:
go all way down the meta editor list, until you see bipd. You should see items such as Jump velocity, or Moving turn speed.
Change the value of Jump velocity to one of the following.
normal jump range: 3-5
Medium Jump range: 5-7
High jump range: 7-15
If you want no fall damage, click flags, then immune to fall damage.
Then click poke.
---------------------------
Finished!
Last edited by a moderator: