Solved Ask for information Xkit X360ACE V4

Discussion in 'Xbox 360 Support' started by Hafidi, Dec 5, 2018 with 44 replies and 1,132 views.

  1. Hafidi

    Hafidi Newbie

    Messages:
    34
    Ratings:
    0
    Hello community members,

    I've already have some experience with PS3 Jailbeak but this it will be my first step and try to jailbreak Xbox .
    Some tools i have :
    • Xbox 360 Slim 2010-05-10 12v---10.83 Model 1439 ( Trinity i think ) .
    • Chip X360ACE V4 .
    • Nand X .
    • CPU Post Fix Adapter.
    • All soldering and repair tools .( I've a phone repair shop )
    My question is with what should i start ?

    Any advises are welcome just be patient with me i'm noob with Xbox world .
     
  2. OP
    Hafidi

    Hafidi Newbie

    Messages:
    34
    Ratings:
    0
    Also please what is P1 and P2 modes ? what is the different ?
     
  3. Ephemeral

    Ephemeral Memento Mori

    Messages:
    307
    Ratings:
    77
  4. OP
    Hafidi

    Hafidi Newbie

    Messages:
    34
    Ratings:
    0
  5. Ephemeral

    Ephemeral Memento Mori

    Messages:
    307
    Ratings:
    77
    • Like Like x 1
  6. OP
    Hafidi

    Hafidi Newbie

    Messages:
    34
    Ratings:
    0
  7. XeDevn

    XeDevn Enthusiast

    Messages:
    314
    Ratings:
    30
    Yes you’ll be able to backup games.
     
    • Like Like x 1
  8. OP
    Hafidi

    Hafidi Newbie

    Messages:
    34
    Ratings:
    0
    Well thank you sir, i'll post my experiment, i hope everything will be fine.
    Is there anything to be care about it?
     
  9. XeDevn

    XeDevn Enthusiast

    Messages:
    314
    Ratings:
    30
    No problem! Just be careful soldering really. Use plenty of flux, don’t hold onto a point very long, and most importantly practice! If you have any kind of circuit board just practice soldering onto pads. There’s also plenty of good soldering tutorials on YouTube. Just don’t rip a pad and you’ll be ok! Lol
     
  10. OP
    Hafidi

    Hafidi Newbie

    Messages:
    34
    Ratings:
    0
    Thank you, i'll try it .
    Please Administrators don't close thread till i report results .

    Best regards.
     
  11. OP
    Hafidi

    Hafidi Newbie

    Messages:
    34
    Ratings:
    0
    soldering done i have started with P2 mode ,
    like i said i have ACE V4 what i need to do next ?
     
  12. Newsk

    Newsk Getting There

    Messages:
    2,457
    Ratings:
    313
    Very first step is; read the nand getting 2 matching nand dumps.(back them up outside of jrunner ) Then create ecc image and write it to the nand . Have you done that ?
     
    • Like Like x 1
  13. OP
    Hafidi

    Hafidi Newbie

    Messages:
    34
    Ratings:
    0
    Thank you for reply, which software i need to use and which pinouts should i follow ?
     
  14. OP
    Hafidi

    Hafidi Newbie

    Messages:
    34
    Ratings:
    0
    i'm sorry i'm newbie be patient with me, because i've seen many videos and topics and many users said that the ACE V4 little different from V3 . i don't know and i don't want to take any risks .
     
  15. Newsk

    Newsk Getting There

    Messages:
    2,457
    Ratings:
    313
    Jrunner . And just follow install from aces website
    Here
    http://x360ace.com/V4.1/
    Personally I prefer acev3's on trinity's because you can use 15432s amazing timing files
     
    • Like Like x 1
  16. OP
    Hafidi

    Hafidi Newbie

    Messages:
    34
    Ratings:
    0
    Thank you i will keep it in my mind next time, i've found 0.3 beta of jrunner is it ok ?
     
  17. OP
    Hafidi

    Hafidi Newbie

    Messages:
    34
    Ratings:
    0
    my ace v4 already installed i'm stuck now with nand-x standalone version and jrunner , how to proceed ?
     
  18. Newsk

    Newsk Getting There

    Messages:
    2,457
    Ratings:
    313
    . I would first make sure the console still boots by removing the 3.3v from the chip and boot it up . Assuming it still boots move forward with reading your nand using your nand x and jrunner. You'll need to install the nandx driver on your pc to get jrunner able to use it.

    To install driver u have to disable driver signature enforcement(wont work otherwise ) then plug it in to USB and find it in device manager then right click and manually install driver . Point it to the jrunner folder/common/drivers . Then say install anyways when prompted.
     
  19. OP
    Hafidi

    Hafidi Newbie

    Messages:
    34
    Ratings:
    0
    thank you man ♥ i'll post updates of my work :wink:
     
  20. OP
    Hafidi

    Hafidi Newbie

    Messages:
    34
    Ratings:
    0
    hi guys , how suppose i find cpu key ?
     

Share This Page