What's new

Solved About about jtag and rgh

  • Thread starter juthegame
  • Start date
  • Views 675
J

juthegame

Newbie
Messages
89
Reaction score
1
I havehbeen researching on how to jtag and rgh xbox 360 l downloaded jrunner program and I came across how to install coolrunner rev c that is wire install and I couldn't understand the following.please need help because I don't want to get help from outside.which are as follows

1)Can you use a coolrunner rev c on a phat xboX 360 direct installation without qsb?
2)I don't understand what it means by default (jumper closed) alternative (jumper open)
3) what's the difference between rgh1 and rgh2?
4) And how to go about rgh1 and rgh2 on both phats and slim
5)rgh1(jumper closed) and rgh2(jumper open)
 
N

Noobert

RGH/Flashing Support
VIP
Retired
Messages
8,385
Reaction score
4,624
I havehbeen researching on how to jtag and rgh xbox 360 l downloaded jrunner program and I came across how to install coolrunner rev c that is wire install and I couldn't understand the following.please need help because I don't want to get help from outside.which are as follows

1)Can you use a coolrunner rev c on a phat xboX 360 direct installation without qsb?
2)I don't understand what it means by default (jumper closed) alternative (jumper open)
3) what's the difference between rgh1 and rgh2?
4) And how to go about rgh1 and rgh2 on both phats and slim
5)rgh1(jumper closed) and rgh2(jumper open)
  1. Yes, you can do the RGH 1.2 method:
    https://www.se7ensins.com/forums/threads/1349194/
  2. It's referring to JP being bridged or not:
    https://i.gyazo.com/9f1def9e2f4448d83b5924cc5f1bf840.png

    You can see opened on the left, means not bridged.
    Closed on the right is bridged.
  3. Essentially they both do the same thing in the end, but you can only RGH1 a console on 2.0.14699 or lower.
    If you're on the latest Dashboard, 17511, then I'd recommend following the RGH 1.2 guide I linked on #1.
  4. You can't RGH1 a Slim.
    You can only RGH1 a Phat between Dashboard 2.0.8498 - 2.0.14699.
    Any Slim between 2.0.8498 - 2.0.17511 (latest) has to be RGH2.
    Any Phat above 2.0.14699, I'd recommend doing the RGH 1.2 method.
    Any Slim I'd recommend RGHing it with the Ace v3 Chip - don't use a CoolRunner on a Slim.
  5. I answered that in #2.
 
J

juthegame

Newbie
Messages
89
Reaction score
1
Thanks alot
1)What of using a coolrunner rev d on a slim.
2)do I need xecuter post qsb for a slim if am using ace v3 or coolrunner rev d
3)where do I get the original ace v3 because the last time I checked the are going bad
4)do I also need to 4gb Nand r/w kit if am working on a Corona 4gb
5)I was trying to rhg a phat I connected the Nand x wire to the motherboard,and I clicked on read Nand and on the xebuild tab it detected a falcon,it changed from retail to jtag and the nands where the same.my question is don't you have to choose between jtag,rhg and rgh2
 
N

Noobert

RGH/Flashing Support
VIP
Retired
Messages
8,385
Reaction score
4,624
Thanks alot
1)What of using a coolrunner rev d on a slim.
2)do I need xecuter post qsb for a slim if am using ace v3 or coolrunner rev d
3)where do I get the original ace v3 because the last time I checked the are going bad
4)do I also need to 4gb Nand r/w kit if am working on a Corona 4gb
5)I was trying to rhg a phat I connected the Nand x wire to the motherboard,and I clicked on read Nand and on the xebuild tab it detected a falcon,it changed from retail to jtag and the nands where the same.my question is don't you have to choose between jtag,rhg and rgh2
  1. I'll assume you mean what if using a CoolRunner Rev D on a Slim.
    You can use any chip you want, I just suggested the Ace v3 because they're $8 and give you the best boot times.
    If you're using a CoolRunner Rev D, that's fine - But it'll depend on which motherboard you have.
    You will install it the same exact way as a Rev C, because it's the same points.
    The only difference would be Point B (STBY_CLK).

    The CoolRunner Rev D has a 48MHz Crystal on it, so you can either keep the R13 resistor under it bridged or un-bridged.
    If you keep it bridged, you don't have to use Point B.
    If you keep it un-bridgde, you do have to use Point B.

    However, that's for Phat and Trinity.
    Coronas require the R13 Resistor to be bridged.
  2. The Post Out QSB is required for Corona v3/4/5/6.
    Regardless of which chip you pick.
  3. You can get them straight from eBay.
    There was a shipment of bad ones a couple of months ago, but they should be fine now.
  4. Yes, you need the 4GB R/W kit for Corona v2/4/6.
  5. There are ones for you to pick from on the top right of J-Runner.
    You'd choose the correct one based off of whichever Dashboard you're on.
 
J

juthegame

Newbie
Messages
89
Reaction score
1
1)But how is it that my Corona 4gb has only a coolrunner rev d,no tx 4gb kit and qsb.
2)what should be done if a chip that's ace v3 has some components which are burnt,and light is not flashing but the other one is on
3)
 
3)Does the jrunner come with dashboards or you have to download them.
 
N

Noobert

RGH/Flashing Support
VIP
Retired
Messages
8,385
Reaction score
4,624
1)But how is it that my Corona 4gb has only a coolrunner rev d,no tx 4gb kit and qsb.
2)what should be done if a chip that's ace v3 has some components which are burnt,and light is not flashing but the other one is on
3)
 
3)Does the jrunner come with dashboards or you have to download them.
  1. I'm not sure what you're asking?

    There are 3 different 4GB Corona revisions:
    Corona v2, v4, and v6.

    Corona v2 requires the CoolRunner Rev D, and the 4GB R/W Kit.
    Corona v4 and v6 requires the CoolRunner Rev D, 4GB R/W Kit, and the Post Fix Adapter.

    I don't know which version you have.

    You do not need to buy the QSB.
    All it does is clean up the install, it is not needed.
  2. It depends on which components are burnt.
    I'd need to see a picture of the chip.
  3. You'd have to find the files and download them.
 
J

juthegame

Newbie
Messages
89
Reaction score
1
1)It's a Corona v2.
2)How do I upload the pictures because last time I failed.
3)where can I download the files.
4)this new Xbox 360e which one can be rgh since the are two versions and I heard that one can be rgh and the other one can't be rgh.
4)is it advisable to use a 4gb kit made of a SD adapter
 
N

Noobert

RGH/Flashing Support
VIP
Retired
Messages
8,385
Reaction score
4,624
1)It's a Corona v2.
2)How do I upload the pictures because last time I failed.
3)where can I download the files.
4)this new Xbox 360e which one can be rgh since the are two versions and I heard that one can be rgh and the other one can't be rgh.
4)is it advisable to use a 4gb kit made of a SD adapter
  1. Then all you need is the Glitch Chip, like a CoolRunner Rev D or Ace v3 - and the 4GB R/W Kit.
  2. Upload to Imgur and post the URL.
  3. [Click here to view this link]
    https://www.virustotal.com/#/file/b...0d400474f8d8d32e24edfa5f58a4dd6767c/detection

    Extract that, and place those folders in the J-Runner/xebuild/ folder.
  4. There's 3 different motherboards in the 360E.

    There's the Corona v5, and v6 - both of which can be RGHed.
    The third one is the Winchester motherboard - that cannot be RGHed.
    You can check here for how to identify if it's a Winchester by looking at the pictures:
    http://team-xecuter.com/forums/threads/147484-New-Xbox-360-Winchester-Motherboard
  5. You can if you want, I use this one:
    http://themodshop.co/shop/sd-tool.html
 
J

juthegame

Newbie
Messages
89
Reaction score
1
i uploaded the pictuers "burnt components - Album on Imgur
"

1)can you update the xbox which is rgh with the update downloaded from xbox.com using a usb flash driver?
2)i dont have the original nand,cpu key and dvd key
3)how to i go about using xebuild seen the chip is not working and i only have coolrunner rev d which needs to be programmed and they is need to write the timing files to the chip?
4) do i need to delete all the files which are in xebuid folder inorder to peste the ones in the xebuild folder i downloaded?
 
Last edited:
J

juthegame

Newbie
Messages
89
Reaction score
1
I downloaded the files xebuild and put them in the xebuild,I did everything from reading the nand got the CPU key am stuck on create xebuild,it will start creating the xebuild image then kv info saved to file,and then failed
 
Top Bottom