I DONT TAKE RESPONSIBILITY BUT I DONT THINK THERE WILL BE ANYTHING TO TAKE RESPONSIBILITY FOR!
NOTE THAT THIS IS NOT MINE all credit goes to Igor Bov a master at these things and has many other TUT's
HERE IT IS
Tools of Trade
What you need to have is a set of Screw Drivers, among them a Torx 10(T10) and a Torx 8(T8) screw drivers. Other than that the fix itself will require the following:
- Arctic Silver 5 thermal paste
- 32 5mm flat washers
- 8 M5 x .8 x 10mm screws
You should be able to buy AS5 for under $10, and the rest should not cost more than $5, if you don't already have washers and screws. You can pick those up at any hardware department store.
STEP 1 Opening Up The Xbox 360
It might seem a little difficult, but really there's nothing to it.There is very well done and detailed video on how to open your Xbox 360 on youtube the link is <a href="http://www.youtube.com/v/LXwXC1IE_ck" target="_blank">
http://www.youtube.com/v/LXwXC1IE_ck...?v=LXwXC1IE_ck
Contrary to what some people might say, you do NOT need any kind of special tools to open the xbox 360. I've used a pair of nail bitting scissors. But really anything long, thin and hard enough to fit through those ventilation holes will do the job just fine. I would recommend a very thin steel philips screw driver.
Now if that video wasn't detailed enough, you can follow this link(
How to open/dissassemble a 360 case) for more information. After you removed the DVD drive, simply pull out the white heatpipe, unhook the fan from the motherboard, pull it towards you and pull it out.
Congratulations, you have successfully disassembled your Xbox 360
STEP 2 FIXING RROD
Once you have taken a part (well partially) your 360, you should by now have something that looks like this
Now lets remove the motherboard from the metal casing. Look at the powerswitch in the front. There are 3 Torx8 (T8) screws that you must remove. One of them is concealed by that white light diffuser. Memorize the position it is attached, so that you don't accidently clip it on wrong, just to find out your 360 won't turn on AFTER you reassemble it.
After you remove the T8 screws, simply pull out the chip and set it aside. In some versions of the 360 there are a bunch of T8 screws that hold the motherboard from the bottom of the case. Unscew those, and your motherboard should come out of the metal casing.
Flip the motherboard over and face the culprit that has plagued your 360. Microsoft's ingenuis Xclamps design. These Xclamps are the reason why your Xbox 360 gets the 3 red lights. My guess is that somebody got really stoned one night and decided to hold in these brackets by pressure, instead of the logical, conventional... screws. Instead of evenly distrubiting the pressure, it pushes down on the back of the cpu and gpu chips. When the 360 gets hot, the motherboard flexes. The combination of that and the xclamps pressing down on the chips causes the cheap bga solder connections underneath the chips to break. This is why the towel trick temporarily fixes this, it reflows the solder to create the connections again, but the xclamps are still there to screw it up again.
Indulge yourself in prying those pieces of **** off the motherboard. I used pliers to get them off, but be VERY cautious not to damage the motherboard itself while you're at it. You must pry off 2 out of 4 ends before they pop off.
After removing the Xclamps, flip the mobo over to remove the heatsinks from the CPU(left) and the GPU(right, 2 chips; 1 big 1 small). Now stop, and lets take a moment to applaud to microsoft's awesome thermal paste job, it looks like very few of it actually ended up on the CPU/GPU to conduct the heat released from the chips to the heatsinks. Great job microsoft.
Use a 1/4" socket to remove the screws from both heatsinks.
Lets get the screws ready before we apply the thermal paste. I recommend putting 1 washer on the screw and then 2 washers between the motherboard and the heatsinks so that in case you tighten the screws a little too tight the heatsink won't crush the chip. Now you are ready to apply the Arctic Silver 5 thermal paste.
But before that, I would suggest that you scrub off Microsoft's thermal paste off the heatsinks AND the chips, be careful though not to actually damage the chips. Now put some AS5 on the CPU and on both chips of the GPU. Apply a reasonable amount of this stuff, don't drown the chips in it because it might actually all get squeezed off the chips(just like it did for MS) if you apply too much pressure when screwing back the heatsinks.
Top image is the GPU(2 chips)
Bottom is the CPU
Now it's time to put the heatsinks back on the CPU & GPU with the thermal paste on. Like I said before it is best to put 2 washers between the motherboard and the heatsinks.
The tricky part is to actually screw in the screws onto the heatsinks without flipping the motherboard over. For the obvious reason of course. What I did was simply lift the motherboard up with my hand and turn the screws clockwise until they firmly held the heatsink in place. If you find that a little difficult you can slide the mobo over to the edge of the table just so you can screw them in. Don't screw them in too tight, just enough so that it holds it in place.
You should have something that resembles the picture below. Once again do not overtighten the screws, and don't let them hang there too loosely.
Now plug the front panel(where the On button is) back on, and also the fan. Do not put the heatpipe or the DVD rom in place yet though.
Plug the Xbox in to the power supply and the AV cable.
And turn it on using a remote or your controller. Most likely your 360 will still have the 3 red lights, and the reason for that is because the solder connections are still broken. Let's fix that...
And by let's fix it I mean let's let it fix itself. Turn the 360 on without the heatpipe so that it over heats and resolders the connections. If you get 2 red lights that means the screws are too loose. Correct that and let it stay on for about 10 minutes, until the fan gets to full power. I just let mine overheat until it turned itself off not to fry the CPU/GPU. After it goes off(or you turn it off) let it stand for about 10 more minutes without touching it(otherwise you're screwed if you move it after it resoldered the connections).
Now turn it back on and it should have green lights. If the AV cable isn't plugged you will get 4 red lights, if it is plugged in to your TV, then you probably squeezed the thermal paste off the CPU and GPU while readjusting the screws. My first time repairing the 360 I had to take out the mobo from the metalcasing about a dozen times to make sure everything was done correctly, so if your first time isn't a charm either try the above process several times to get it working.
After you get the green lights, take it a part again(last time I promise) to tighten the heatsinks' screws. Play around with your 360 before closing it up, make sure it works properly.
AND THERE YOU GO YOUR DONE NOW YOU SHOULD NEVER AGAIN I PROMISE GET THE RED LIGHTS OR RROD
How To PERMENATELY Fix The RROD
