What's new

Tutorial How to do the JTAG Hack/Dump NAND/Xell

  • Thread starter EclipseModz
  • Start date
  • Views 1,530,925
Status
Not open for further replies.
Cybergate

Cybergate

Enthusiast
Messages
581
Reaction score
66
Points
95
Sin$
0
this is hard
 
E

EclipseModz

VIP
VIP
Retired
Messages
7,688
Reaction score
2,715
Points
655
Sin$
0
ll V1oLeNT ll said:
After the the Xell is dumped to the 360 do you still need to use a vga cable with the 360 to see xell booting to the blue screen?
Nope, you can use your standard HD or regular video cables.
 
A

angel31984

Newbie
Messages
17
Reaction score
4
Points
45
Sin$
7
Ok so i just installed the jtag hack and the lpt to my 360, I extracted the orig.bin, orig2.bin and orig3.bin the only ones that matched where orig2 and orig3 so i extracted the rawkv.bin and rawconfig.bin and enjected them in to the xbr 8955.bin and do the comand nandpro lpt: -w16 xbr 8955.bin. It installed after that i unpluged the power for about a min. and powerd it on but i get the e79 error so i tried to turn it on with the control pulged in to the rear usb and still the same thing :cursing: . i used the degraded also oped with no errors.
this is what degraded read out

CB Version: 1903 LDV0
CD Version: 1888
CE Version: 1888
CF(0)Version: 6683 LDV4
CF(1)Version: 5766 LDV3

Thank you and any help would be appreciated.
 
Scar

Scar

VIP
VIP
Retired
Messages
5,114
Reaction score
1,496
Points
670
Sin$
0
angel31984 said:
Ok so i just installed the jtag hack and the lpt to my 360, I extracted the orig.bin, orig2.bin and orig3.bin the only ones that matched where orig2 and orig3 so i extracted the rawkv.bin and rawconfig.bin and enjected them in to the xbr 8955.bin and do the comand nandpro lpt: -w16 xbr 8955.bin. It installed after that i unpluged the power for about a min. and powerd it on but i get the e79 error so i tried to turn it on with the control pulged in to the rear usb and still the same thing :cursing: . i used the degraded also oped with no errors.
this is what degraded read out

CB Version: 1903 LDV0
CD Version: 1888
CE Version: 1888
CF(0)Version: 6683 LDV4
CF(1)Version: 5766 LDV3

Thank you and any help would be appreciated.
Make a new XBR file and only write the rawkv to it, leave out the config file, then write that. For some reason the config file screws it up.
 
A

angel31984

Newbie
Messages
17
Reaction score
4
Points
45
Sin$
7
Scar said:
Make a new XBR file and only write the rawkv to it, leave out the config file, then write that. For some reason the config file screws it up.

thanks i'll when my 360 finishes installing the same xbr for the 3 time i thought i would install it a couple of more times before i gave up i will post with my results.

Scar said:
Make a new XBR file and only write the rawkv to it, leave out the config file, then write that. For some reason the config file screws it up.

Ok i tried it but still no go. Any other suggestions.
 
E

EclipseModz

VIP
VIP
Retired
Messages
7,688
Reaction score
2,715
Points
655
Sin$
0
Make sure that your jtag points are soldered correctly. If not then you will get E79
 
A

angel31984

Newbie
Messages
17
Reaction score
4
Points
45
Sin$
7
EclipseModz said:
Make sure that your jtag points are soldered correctly. If not then you will get E79

Thanks ill desolder the wires and add the left over clippings from the diodes so i can be sure that the it is in there correctly thanks and ill post with results.
 
D

DONTuseKYJELLY

Banned
Messages
218
Reaction score
38
Points
85
Sin$
0
What were your settings for testing the LPT wiring.
 
E

EclipseModz

VIP
VIP
Retired
Messages
7,688
Reaction score
2,715
Points
655
Sin$
0
ooo For the multimeter. I put it on 200ohms

Correction 200K ohms
 
E

EclipseModz

VIP
VIP
Retired
Messages
7,688
Reaction score
2,715
Points
655
Sin$
0
So all your wires are to the correct pin # correct?
 
dontmockme360

dontmockme360

Enthusiast
Messages
167
Reaction score
61
Points
135
Sin$
7
I went and got a brand new console today, the 60GB bundle for only $190 and it was made in 2008 so im super happy
 
E

ElDudeorino

Newbie
Messages
3
Reaction score
0
Points
35
Sin$
0
So do you unsolder the LPT cable after this is done, or can you leave it attached? I guess if there is an update you will have to solder it back on?
 
E

EclipseModz

VIP
VIP
Retired
Messages
7,688
Reaction score
2,715
Points
655
Sin$
0
You need to build a usb programmer if you want to use usb. That or buy a cygnos chip and install that then you can use usb.
 
dontmockme360

dontmockme360

Enthusiast
Messages
167
Reaction score
61
Points
135
Sin$
7
Help!
C:\Documents and Settings\Owner>C:\Nandpro20b\nandpro.exe lpt: -r16 nand1.bin
NandPro v2.0b by Tiros
Testing LPT device address:0378
Testing LPT device address:0278
Testing LPT device address:03BC
Could not detect a flash controller!
Can not continue
 
Status
Not open for further replies.
Top Bottom
Login
Register